|
SAFETY WARNING
|
Safety Warning / Before Installation>> Please
refer to this PDF file(45.2KB).
|
| HOW TO INSTALL & TROUBLE
SHOOTING |
|
Installation of DIN-Gauge >> Please
refer to this PDF file(269KB).
How to attach sensors >> Please
refer to this PDF file(46.9KB).
|
| FINAL CONFIRMATION
AFTER INSTALLATION |
 |
 |
After installation, check that no materials or
tools remain in the driver's seat or the engine compartment.
If there are tools at the feet of the driver's seat, this ma
cause brake operation failure because of tools or materials
caught under the brake pedal. If there are tools in the engine
compartment, the engine may be damaged. |
|
Please be sure to check the following items. Otherwise,
there is a possibility that a serious accident may occur. |
 |
Ensure that all hoses and tubing are properly
attached. Also ensure that there is no leakage of oil, fuel,
water and exhaust. |
|
Check that the sensor and wires are not interfering
with the engine. |
|
Ensure that devices associated with the ignition
(ie. ignition coil, distributor, plug cord, etc.) were not damaged
or disconnected during the installation of the sensors and wires. |
|
Ensure that the DIN-Gague and wires are tightly
attached, so they don't come loose and hinder driving. |
|
Check that all wires disconnected from the vehicle
during installation have been properly reattached. |
|
Ensure that the negative battery terminal is
tightly attached. Close the hood properly. |
 |
|
A protection sheet is stuck to the glass for protection. Please
remove the sheet in the customer's presence after installation
of the product. |
|
| HOW TO OPERATE |
|
|
Please check meters after starting the engine
and be sure there are no abnormalities in the car's function.
If you start to drive without checking, there is a possibility
an accident may occur. |
|
| TURNING ON
and OFF POWER |
|
Once the ignition key is turned on, gauges come
into operation after the needle pointers of three gauges move
sequentially (opening mode). |
|
Once the ignition key is turned off, gauge operations
stop after the needle pointers of three gauges move sequentially
(closing mode). |
|
| ILLUMINATION |
|
The gauge dials and needle pointers light up
being interlocked with switching on and off of the illumination
of the vehicle. |
|
The illumination of the gauge dials and needle
pointers lights up during the opening and closing modes without
reference to the illumination of the vehicle. |
|
| CHECK FUNCTIONS |
| Wire disconnections and short circuits of sensors and
sensor wires can be checked by movement of pointers. If the pointers
move as follows after installation of the product, please contact
the installation personnel. |
 Wire
disconnection check |
|
This function reports the wrong wiring and/or disconnected sensors
and wires. The pointer of a gauge which the wire is disconnected
moves between 250 and 260 degrees at the same interval as follows:
The movement indicates the angle of pointers.
All the pointers of three meters do not move simultaneously.
|
| Short
circuit check |
|
This function reports the short circuits of sensors and wires.
The pointer of a gauge which has a short circuit moves between 10
and 20 degrees at the same interval as follows:
The movement indicates the angle of pointers.
All the pointers of three meters do not move simultaneously.
|
| CONVERSION
TABLE |
|
TEMPERATURE
|
|
|
|
|
0
|
32
|
|
10
|
50
|
|
20
|
68
|
|
30
|
86
|
|
40
|
104
|
|
50
|
122
|
|
60
|
140
|
|
70
|
158
|
|
80
|
176
|
|
90
|
194
|
|
100
|
212
|
|
110
|
230
|
|
120
|
248
|
|
130
|
266
|
|
140
|
284
|
|
150
|
302
|
= 
x 9/5 + 30 |
|
|
PRESSURE
|
|
kPa
|
PSI
|
|
0
|
0.0
|
|
50
|
7.3
|
|
100
|
14.5
|
|
150
|
21.8
|
|
200
|
29.0
|
|
250
|
36.3
|
|
300
|
43.5
|
|
350
|
50.8
|
|
400
|
58.0
|
|
450
|
65.3
|
|
500
|
72.5
|
|
550
|
79.8
|
|
600
|
87.0
|
|
650
|
94.3
|
|
700
|
101.5
|
|
750
|
108.8
|
|
800
|
116.0
|
|
850
|
123.3
|
|
900
|
130.5
|
|
950
|
137.8
|
|
1000
|
145.0
|
|
1kPa = 0.145 PSI
|
|
|